GWR (ex ADR 18) 679

davey4270

Western Thunderer
View attachment 86368 I am revving up to make one of these in 7mm from the Agenoria kit.

I believe this was one of the favoured Stamper designs but I still expect some clearance issues as this is one small prototype.

I was inspired by this high res shot of a private owner B1 named Judith in Stafforshire. Seems as though there were not many of this design built and I'll bet very few kits were sold in either scale.
 

davey4270

Western Thunderer
2F07301F-12EA-49CE-965B-DC6DC2F811E8.jpeg BA7B4E38-34C2-4057-BC52-87BAA2281C9B.jpeg 2F07301F-12EA-49CE-965B-DC6DC2F811E8.jpeg 2F07301F-12EA-49CE-965B-DC6DC2F811E8.jpeg I have almost completed 679 with no problems. I have used a Dragon Models 15/25 motor with the supplied motor mount and Branchlines 40:1 gears. Wiper pickups as suggested but but move them forward of the sand pipes (reverse positions).
View attachment 86368 I am revving up to make one of these in 7mm from the Agenoria kit.

I believe this was one of the favoured Stamper designs but I still expect some clearance issues as this is one small prototype.

I was inspired by this high res shot of a private owner B1 named Judith in Stafforshire. Seems as though there were not many of this design built and I'll bet very few kits were sold in either scale.
use a Dragon Models 15/25.
 

davey4270

Western Thunderer
A bit like this. Boiler/tank just sitting there.
Only have etches so castings will be problematic unless a sourse can be suggested by anyone
Also have no clues as to suitable motor. Not much room as it's so small.

I just found your post while looking for something else. I tried to reply on my phone last night but the only thing it did was to move this post to the top of my list???
Anyway, I have used a Dragon Models 15/25motor which fits without having to cut the other end shaft. They make a 15/35 which is very powerful and with the shaft cut may be the same length but the curvature of the tank may be a problem. Ragstone Models are reintroducing the Agenoria range on behalf of Mike Williams and may help you with the castings if you ask them nicely. My 679 is virtually complete and in Dai the Paint's studio.

IMG_4106.jpg

IMG_4107.jpg
 

LaScala

Member
I just found your post while looking for something else. I tried to reply on my phone last night but the only thing it did was to move this post to the top of my list???
Anyway, I have used a Dragon Models 15/25motor which fits without having to cut the other end shaft. They make a 15/35 which is very powerful and with the shaft cut may be the same length but the curvature of the tank may be a problem. Ragstone Models are reintroducing the Agenoria range on behalf of Mike Williams and may help you with the castings if you ask them nicely. My 679 is virtually complete and in Dai the Paint's ststu

View attachment 100294
Thanks for Ragstone tip Dave. That's looking very neat indeed. You might remember I used ABS castings which were hard to prize out of the Swain horde. I would have liked the combined dome/safety valve but used the short ABS one. I might change it if Ragstone can oblige.
 

Attachments

  • 20181217_174157.jpg
    20181217_174157.jpg
    624.5 KB · Views: 27

davey4270

Western Thunderer
Thanks for Ragstone tip Dave. That's looking very neat indeed. You might remember I used ABS castings which were hard to prize out of the Swain horde. I would have liked the combined dome/safety valve but used the short ABS one. I might change it if Ragstone can oblige.
Very nice. I’m spraying the green at the moment. I’ll leave it a few days to harden before masking to spray black. Hopefully be reassembled by next weekend. Just noticed from pictures that the lower part of the chimney is painted green the same as the tank. Most unusual !
 

davey4270

Western Thunderer
0CB74CC3-EE28-4D2C-A41D-63C20B879BBE.jpeg
A bit like this. Boiler/tank just sitting there.
Only have etches so castings will be problematic unless a sourse can be suggested by anyone
Also have no clues as to suitable motor. Not much room as it's so small.
I managed to squeeze one of Dragon Models 15/25 in without cutting the shaft, flats to front and back. 40:1 gears with the supplied Agenoria motor mount but I did have to elongate the slots.
A bit like this. Boiler/tank just sitting there.
Only have etches so castings will be problematic unless a sourse can be suggested by anyone
Also have no clues as to suitable motor. Not much room as it's so small.
 
Top